Motton sheet metal production floor

Home / Manufacturing Capabilities

Manufacturing capability 02

Metal Laser Cutting

Repeatable sheet metal profiles, holes, slots and cut-outs prepared for bending, welding, finishing and assembly.

What metal laser cutting does

A focused beam cuts a programmed profile through sheet material.

Laser cutting converts a flat-pattern file into cabinet panels, brackets, enclosure faces and other sheet metal blanks. External contours, holes, slots and ventilation patterns can be produced in the same operation, keeping their positional relationship consistent across a batch.

The cutting file must match the approved drawing revision and material thickness. Cut parts are then identified and routed to forming, joining or finishing according to the production plan.

Its role in custom metal manufacturing

Accurate blanks give downstream operations a stable starting point.

Hole location, notch geometry and overall blank dimensions affect bend position, weld fit-up and final assembly. A clean, consistent blank reduces manual correction and helps repeated parts fit the same fixture or hardware.

Nesting also influences material use and part handling. Parts that share a sheet must still be separated, identified and protected in a way that suits their finish and cosmetic-face requirements.

Relevant applications

  • Cabinet sides, backs, doors, roofs and shelf blanks
  • Enclosure panels with cable, display or connector openings
  • Ventilation slots, louvre preparations and perforated patterns
  • Mounting plates, brackets, gussets and reinforcement pieces
  • Hinge, lock and handle cut-outs
  • Flat-pack panels with locating tabs and fixing holes

Examples of finished products are shown on our custom metal cabinets, custom metal enclosures and sheet metal fabrication pages.

Important technical considerations

  • Closed vector profiles, correct scale and one uncontaminated cutting layer
  • Kerf compensation where the drawing requires it
  • Hole diameter, web width and slot geometry relative to material thickness
  • Heat input and distortion on large, thin or highly perforated panels
  • Part retention, tab placement and safe removal from the nest
  • Edge condition, burr allowance and any later deburring requirement
  • Cosmetic-face protection and scratch control during unloading

Features close to a bend must also be reviewed for distortion. A cut file can be geometrically correct while still being unsuitable for the finished formed part.

Materials and thickness review

Mild steel, galvanised steel, stainless steel and aluminium each respond differently to cutting energy, assist gas and handling. Surface films, zinc coatings and reflective materials require a process appropriate to the actual stock.

Send the exact grade and thickness rather than only a material family. Maximum thickness and sheet envelope are confirmed against the selected equipment and part requirements; no universal rating is assumed for every material.

Cutting limits and drawing information

Sheet size and thickness Confirmed per material, equipment and part geometry during review
Cutting tolerance Confirmed against the drawing and the measurement method
Small holes and narrow webs Reviewed against thickness, heat input and downstream use
Edge finish As cut, deburred or otherwise finished as specified
Flat-pattern files DXF or DWG exchange data checked against the approved PDF or model

Laser cutting does not correct poor flat-pattern development. If the blank folds into a different dimension from the drawing, the issue must be resolved during engineering review, not at the cutting machine.

Manufacturing limitations

Very small features, thick material, highly reflective stock, heat-sensitive films and tightly nested perforations can impose process limits. Large thin panels can move as internal stress is released, and cut edges may need additional dressing where handling safety or appearance requires it.

Where a feature is not suitable for laser cutting, we discuss an alternative such as changing the geometry, adding a secondary operation or using a different process before quotation.

Related capabilities

Most blanks continue to CNC sheet metal bending. Joined assemblies move to metal welding, while final dimensional checks are covered by manufacturing quality control.

Metal laser cutting — common questions


What file should we send for laser cutting?

A clean DXF or DWG flat pattern is useful, together with a dimensioned PDF or STEP model for verification. State the material, thickness, drawing revision and which side is cosmetic.


Can holes and ventilation patterns be cut in the same operation?

Yes, profiles, holes, slots and repeated ventilation patterns are normally programmed on the same blank, subject to geometry, heat and handling review.


Will laser-cut parts be ready for powder coating?

Cut parts may still require deburring, forming, welding or surface preparation. The required edge condition and finishing route are confirmed from the drawing and product use.


How tight a tolerance can laser cutting hold?

It depends on material, thickness, part geometry, thermal behaviour and measurement method. Send the tolerance on the drawing so it can be reviewed instead of relying on a generic figure.


Request a laser cutting review

Send the flat pattern, material, thickness and quantity. We check the blank and its downstream operations before quoting.