Forming equipment in the Motton factory

Home / Manufacturing Capabilities

Manufacturing capability 03

CNC Sheet Metal Bending

Programmed press-brake forming for panels, flanges, channels and enclosure sections, with bend feasibility reviewed before production.

What CNC sheet metal bending does

A press brake forms a flat blank along programmed bend lines.

CNC bending uses controlled ram movement and backgauge positioning to produce repeatable angles and flange dimensions. Multiple bends can turn a laser-cut blank into a cabinet side, door pan, enclosure cover, bracket or reinforced shelf.

The flat pattern, bend sequence and tooling must work together. The review therefore considers the formed geometry, not just whether each individual angle can be made.

Its role in metal manufacturing

Forming gives sheet metal stiffness, shape and assembly interfaces.

Folds can replace separate reinforcement, create return edges, locate mating panels and define door or roof profiles. Consistent bending helps holes line up during assembly and keeps visible gaps uniform across a cabinet run.

Bending also changes the effective dimensions of the blank. Material is stretched and compressed around each bend, so bend allowance and the chosen measuring convention must be resolved before cutting.

Relevant applications

  • Cabinet bodies, doors, shelves and folded reinforcement
  • Enclosure covers, trays, mounting brackets and chassis
  • Roof panels, drainage edges and weather-return profiles
  • Flat-pack panels with locating folds and fastening flanges
  • Channels, angles, hat sections and simple stiffening profiles
  • Workbench panels and industrial cabinet frames

These forms are used in outdoor storage cabinets, custom enclosures and industrial metal cabinets.

Important technical considerations

  • Inside bend radius, bend allowance and the flat-pattern convention
  • Material grain direction where cracking or cosmetic appearance matters
  • Minimum flange length and access to the backgauge
  • Hole-to-bend distance and distortion of slots near bend lines
  • Bend reliefs at intersecting flanges and closed corners
  • Tooling clearance, part collision and the order of bends
  • Springback and angle compensation by material and thickness
  • Protection of coated faces, films and decorative stainless finishes

Materials and forming behaviour

Mild steel is generally straightforward to form when grade and bend radius are suitable. Galvanised sheet requires attention to coating condition at the bend. Stainless typically needs different force and springback compensation, while aluminium grade and temper strongly affect crack risk.

The drawing should state material grade, thickness and any mandatory inside radius. If grain direction is important to appearance or performance, mark it so nesting and forming follow the same requirement.

Bending specification and confirmation

Formed geometry Checked from the approved drawing or 3D model
Bend length and tonnage Confirmed against the selected tooling and equipment
Angle and linear tolerance Applied from the drawing or agreed in writing
Tooling and bend sequence Selected after collision, access and flange review
Surface protection Specified for cosmetic faces, films and coated stock

Actual machine capacity and achievable tolerances are confirmed for the specific part during engineering review. Send the part drawing so feasibility can be assessed without relying on a generic maximum.

Manufacturing limitations

Deep boxes, short return flanges, closed profiles, hems and bends near large cut-outs can restrict tool access or sequence. Some shapes need a design revision, special tooling or a different construction rather than a single press-brake setup.

Sharp bends in unsuitable material can crack, and an unspecified radius can produce a part that cannot be formed consistently. Load-bearing performance must not be inferred from the formed shape alone; it requires a defined load case and suitable validation.

Related capabilities and products

Bending starts with a verified flat pattern from drawing review and laser cutting. Formed parts may then move to welding, surface finishing and product assembly.

CNC sheet metal bending — common questions


Can you bend a closed box or deep return?

It depends on flange dimensions, tool clearance and bend order. Send the section drawing or 3D model so tool access and part collision can be reviewed.


Why do you need the material grade for a bend review?

Grade, temper and thickness affect force, springback, minimum radius and crack risk. A flat pattern developed for one material may not produce the same formed dimensions in another.


Can holes be placed next to a bend?

Only when their shape and position remain acceptable after forming. Hole-to-bend distance, slot orientation and distortion are checked during drawing review.


Do you develop the flat pattern?

A flat pattern can be prepared or checked as part of the manufacturing review. Critical formed dimensions and the bend-radius convention must be approved before cutting.


Send a formed part for review

Share the drawing or STEP model, material and quantity. We check bend sequence, tooling access and open tolerance questions.